CE 78 Perfect Filler & Finisher
READY-MIXED FILLER
FOR PLASTERBOARD JOINTING AND FINISHING
ADVANTAGES
- easy to smooth
- Easy to sand
- Stronger adhesion
- Minimal shrinkage
TECHNICAL DEFINITION
TECHNICAL CHARACTERISTICS. • Tape adhesion: > 1,000 g. • Density: 1.80 to 1.85. • Solid content: 72 to 77% • VOC content: less than 1 g/l. • Film thickness: 1 to 5 mm. • Fire rating: A2 -S1, d0.
TECHNICAL CHARACTERISTICS. • Tape adhesion: > 1,000 g. • Density: 1.80 to 1.85. • Solid content: 72 to 77% • VOC content: less than 1 g/l. • Film thickness: 1 to 5 mm. • Fire rating: A2 -S1, d0.
PACKAGING
20 kg buckets on covered pallets.
20 kg buckets on covered pallets.
COMPOSITION
• Solvents: water. • Reactants: calcium carbonates. • Additives: dispersant, biocide. • Thickeners: cellulose, polyacrylates, clay. • Binders: acrylic dispersant.
• Solvents: water. • Reactants: calcium carbonates. • Additives: dispersant, biocide. • Thickeners: cellulose, polyacrylates, clay. • Binders: acrylic dispersant.
SUITABLE SUBSTRATES
Plasterboard with tapered longitudinal edges (AK/ BA or 4AK/4BA) or with tapered and rounded edges (HRAK/BRA). Painted substrates and renovation. Gypsum blocks, calcium silicate blocks. On walls and ceilings.
Plasterboard with tapered longitudinal edges (AK/ BA or 4AK/4BA) or with tapered and rounded edges (HRAK/BRA). Painted substrates and renovation. Gypsum blocks, calcium silicate blocks. On walls and ceilings.
STORAGE
18 months in its original unopened packaging, protected from frost and high temperatures
18 months in its original unopened packaging, protected from frost and high temperatures
SUBSTRATE PREPARATION
SUBSTRATE PREPARATION. Plasterboard must be installed in compliance with the French DTU standards. Cut sheets must be bevelled and dust-free.
SUBSTRATE PREPARATION. Plasterboard must be installed in compliance with the French DTU standards. Cut sheets must be bevelled and dust-free.
USE
Use: the three stages (taping, filling, finishing) must be carried out separately and complied with in accordance with DTU 25-41.
Bazooka: fill the reservoir with the appropriate pump and then apply according to the standard protocol.
Airless sprayer: spray horizontally, standing 20-30 cm away from the substrate. Recommended nozzles: 531 to 535, approx. 100 bar. The airless pump must be fitted with stainless steel balls.
After an initial vertical spray inside the shoulders of the sheets, stretch the tape out along the joint and bed it into the compound using a taping knife. N.B. avoid over-tightening the tape to prevent any risk of bubbling.
After drying, cover the entire surface with a second (filling) coat, using a taping knife to create a smooth finish. Smoothing and skimming: spray with a 627 nozzle and then smooth over with a knife.
Warning: when the product is applied in hot weather, it may dry quickly on the surface. It is advisable to tape the joint quickly after applying the compound to prevent any tape adhesion problems.
Dilution: by bazooka: we recommend the addition of ½ litre of water per 20 kg bucket.
By banjo: add 1.5 litre of water per 20 kg bucket. Clean tools with water.
Use: the three stages (taping, filling, finishing) must be carried out separately and complied with in accordance with DTU 25-41.
Bazooka: fill the reservoir with the appropriate pump and then apply according to the standard protocol.
Airless sprayer: spray horizontally, standing 20-30 cm away from the substrate. Recommended nozzles: 531 to 535, approx. 100 bar. The airless pump must be fitted with stainless steel balls.
After an initial vertical spray inside the shoulders of the sheets, stretch the tape out along the joint and bed it into the compound using a taping knife. N.B. avoid over-tightening the tape to prevent any risk of bubbling.
After drying, cover the entire surface with a second (filling) coat, using a taping knife to create a smooth finish. Smoothing and skimming: spray with a 627 nozzle and then smooth over with a knife.
Warning: when the product is applied in hot weather, it may dry quickly on the surface. It is advisable to tape the joint quickly after applying the compound to prevent any tape adhesion problems.
Dilution: by bazooka: we recommend the addition of ½ litre of water per 20 kg bucket.
By banjo: add 1.5 litre of water per 20 kg bucket. Clean tools with water.
DRYING TIME
A second coat can be applied 12 to 24 hours after the first coat, depending on the ambient conditions
A second coat can be applied 12 to 24 hours after the first coat, depending on the ambient conditions
CONSUMPTION
Joint taping: 500 g/m2/mm of sheets
Skimming: 1 kg/m2 (1 to 4 mm).
Joint taping: 500 g/m2/mm of sheets
Skimming: 1 kg/m2 (1 to 4 mm).
AVAILABLE DOCUMENTATION
DTU 25.41.
NF EN 13963 standard.
DTU 25.41.
NF EN 13963 standard.
PRÉCAUTIONS_DEMPLOI
Do not apply at temperatures below +8°C or above 35°C, nor at humidity levels above 70%.
Do not apply on hot surfaces.
Do not apply on damp surfaces.
Do not apply at temperatures below +8°C or above 35°C, nor at humidity levels above 70%.
Do not apply on hot surfaces.
Do not apply on damp surfaces.
Semin on
social media
